Jae Song | Oct 16, 2018 | 2
Getting to grips with darkroom printing using Caffenol (and alternatives) – Darkroom alchemy – by Mads Madison
Analog black and white film development and chicken soup. Enough internet for today?
An unusual combination, but according to an article I found online, chicken soup can be used to develop film. And the results shown were pretty decent! This find sparked my interest in alternative developers. So, I did some more research and found people trying coffee, tea, wine and even urine as a developer for film.
Getting coffee into my darkroom
After exposing my next film, I discovered that my usual developer had turned into a brown soup. Having all ingredients at home, I decided to give Caffenol-C a shot. The results were amazing.
I obtained a wide range of grays, dark black and a light brown toning for the highlights. I loved the results, so the next logical step for me was to try and print the negatives using Caffenol-C as a paper developer as well.
So I set up my trays, adding one extra tray of water right before the stop bath to wash away all the leftovers of my homemade developer. Since I don’t own any good scales, I decided to use tea spoons as a measurement unit.
You can get all the stuff you need at a supermarket or a drug store:
- 500ml distilled water
- 6 tea spoons instant coffee (use the cheapest one you can get)
- 3 tea spoons vitamin c powder
- 1,5 tea spoons washing soda
The result you get once mixing everything together is a pretty dark and strange smelling liquid. It will not only cure your coffee addiction but makes it pretty difficult to develop from sight as well. I decided to give the paper a quick wash every minute to check it.
Using RC Paper and stopping the clock at 4:30min (the development took quite long compared to regular developers). After 2 prints it took 5 minutes to get a good result, and after 4 sheets I had to mix a fresh batch.
Caffenol to Juicenol, Soupenol, Teanol and other experiements
Still happy about the results, I went grocery shopping and curiosity struck me again. I thought to myself, “If you could use chicken soup to develop film, what else could be used for paper?” So I decided to buy the weirdest things I could think of, resulting with me leaving the store with a variety of juices, children’s mouthwash, tea, hair tonic and buttermilk…yes, hair tonic.
Back at my darkroom I used a variation of the Caffenol-C recipe to mix up another batch:
- 500ml liquid (tea, soup, juice…)
- NO COFFEE
- 3 tea spoons vitamin C powder
- 1,5 tea spoons washing soda
Being scared of total failure, I started by trying the juices with some hard gradation paper. I had beetroot juice, grape juice and carrot juice.
Testing with beetroot, carrots and grapes
The washing soda made the strange smell of the beetroot juice even worse, and the viscous black soup made developing a pain.
I stopped my first try after 10 minutes with no result in sight. I threw the second sheet on the enlarger exposing it for an entire 10 seconds at f5.6. After a fearful 7 minutes of development I finally had a halfway decent low contrast print.
The carrot juice was to follow. It did not need as much exposure and 6:30 minutes later, I had a pretty grainy low contrast print.
To end the “juice-session” I mixed my grape-juice developer which instantly turned from red to green after adding the washing soda smelling almost like a nice wine. A lot of light and 7 Minutes later, I got a pretty dark and red toned print.
Looking at the picture right now, I have to say that I feel a little sad that all of the red faded by now due to exposure to sunlight.
Testing with soup, buttermilk, mouthwash and hair tonic
Working my way through my groceries I decided to use the tomato soup next. There was a nice Mexican smell in the air and I almost felt a little hungry. Both changed after adding the washing soda and I was more than happy that the print took “only” 8 Minutes.
The results had a pretty hard contrast and were the worst so far. It might have worked better using a soft gradation paper. You’re always wiser in hindsight.
The “buttermilk” phase turned into a disaster. I could not manage to get a clean print, there were some small flaky parts sticking to the print blocking the developer. But buttermilk as a developer would be crazy, wouldn’t it?
The last two things left in my shopping bag were mouthwash and hair tonic. Somehow it was impossible to completely dissolve the washing soda leaving me with pretty dark patches where it came in contact with the sheets of paper.
Both the mouthwash and the tonic worked pretty well and provided me with my best results (besides Caffenol) plus developing only took 4:30 Minutes.
It’s not about the coffee
To end this series of experiments, I tried regular tap water mixed with washing soda and vitamin C. It works, but the results were so light that I did not even scan them. I came to the conclusion that it’s not really about what you use as a liquid. It’s about the use of washing soda and vitamin C.
If you look at the basics of printmaking, getting a print means converting exposed silver-halide crystals to macroscopic particles of metallic silver. This is done by using an alkaline liquid and that’s what the washing soda does in my experiments. It turns even acidic liquids into alkaline liquids. The vitamin C just reduces the time needed for development.
I know that the results are not as good as prints done with a “regular” developer. But that was never my goal, my goal was to experiment with photographic material being driven by the question “Will it work?”.
I think I answered that question to my satisfaction.
Thanks for reading!
~ Mads Madison
Write for EMULSIVE
The driving force behind EMULSIVE is knowledge transfer, specifically creating more of it in the film photography community. You can help by contributing your thoughts, work and ideas to inspire others reading these pages.
Take action and help drive an open, collaborative community: all you need do is read this and then drop me a line.
Lend your support
Like what you see here? You can support EMULSIVE by helping to contribute to the community voice on this website (see above), or by heading on over to the EMULSIVE Patreon page and considering financial support from as little as $2 a month.
As if that’s not enough, there’s also an EMULSIVE print and apparel store over at Society 6, currently showcasing over two dozen t-shirt designs and over a dozen unique prints of photographs made by yours truly
In short, I want to continue building this platform and I’d love your help to make that happen.